FileDial › Guides › Video and subtitles

How to remove silence from a video on a Mac

By Himanshu Ranjan · Updated 16 November 2026

To remove silence from a video on a Mac, either split and delete each pause by hand in iMovie, or let a tool find the quiet stretches and cut them for you. With FileDial, run Cut › Remove silences…: it cuts the picture along with the sound and saves a new copy, with two settings for how quiet and how long a gap must be. Nothing is uploaded.

Why cut the silences out

A talking-head video, a lecture or a screen recording usually has more empty time than you notice while recording: a pause to think, a breath before the next point, a few seconds spent looking for the right window. On a phone feed, those gaps are where people scroll away. Removing them is what editors call a jump cut, a cut that removes footage from one continuous shot so the speaker seems to skip ahead slightly. It became a standard look in online vlogs because it keeps the pace up without reshooting.

Cutting dead air also makes a video shorter, which matters when a platform has a length cap or when you want a tutorial to respect the viewer's time. A ten minute recording often loses a noticeable share of its running time once the long pauses go, and nothing the speaker said is lost.

The manual way: QuickTime Player and iMovie

QuickTime Player is fine for the start and end. Apple's guide describes trimming with Edit > Trim: drag the yellow handles in the trimming bar and the parts outside them are removed. That handles a slow lead-in or a fumbled ending, but there is no waveform and no way to find quiet stretches, so it is not practical for removing dozens of pauses in the middle.

iMovie can do the whole job, one pause at a time. It shows audio waveforms in the timeline, so silence appears as a flat stretch. The routine is below. It works and it gives you full control, but a fifteen minute recording can easily hold a hundred pauses, and doing each one by hand takes far longer than the recording itself.

  1. Create a new movie project in iMovie and drag your clip into the timeline.
  2. Zoom in with View > Zoom In (Command-Plus) until the waveform shows clear gaps.
  3. Place the playhead at the start of a pause and choose Modify > Split Clip (Command-B).
  4. Move the playhead to the end of the pause and split again.
  5. Select the short piece between the two splits, delete it, and repeat for the next pause.
  6. Export the finished movie with File > Share > File.

The FileDial way: one tool, a new copy

In FileDial, select the video in Finder, open the dial and choose Cut › Remove silences… It finds the stretches where the sound stays quiet, cuts the picture together with the sound so lips stay in sync, and saves the result as a new file beside the original. The original is never changed, and the result card shows the size before and after, so you can compare and run it again with different settings.

For audio-only files such as a podcast or a voice memo, the same job is Clean › Remove silences… Both work on a batch, so you can select a whole folder of lecture recordings and run one tool on all of them.

If the goal is vertical clips rather than one shorter video, use Cut › Make shorts… Its Cut pauses and filler words switch tightens each clip while the tool adds captions and frames it for 9:16. The video never leaves your Mac. Optional AI picking sends only the transcript text to FileDial's server, and the On this Mac only setting keeps everything on the device.

Settings and trade-offs

There are two settings in Cut › Remove silences… Quieter than sets the level, in decibels, below which the sound counts as silence. The default is -35 dB. Longer than sets how long a quiet stretch must last before it is cut. The default is 0.6 seconds.

Quieter than depends on your recording. In a quiet room with a close microphone, pauses sit well below -35 dB and the default works. With background noise such as a fan, traffic or a busy office, the gaps may never get that quiet, so nothing is cut. Raise the level (for example to -30 dB) so the noise floor counts as silence. Go too far and soft words, trailing syllables and quiet speakers start to disappear.

Longer than controls the rhythm. A low value removes almost every gap and gives the fast, punchy pace of short-form video, but it can feel breathless over a long tutorial. A higher value keeps natural pauses between sentences and only removes the long waits. For a lecture or a calm explainer, a second or more often sounds better than the default. Try a short sample first and listen to the result before running a whole batch.

Pitfalls to watch for

  • Breaths cut too tight. A breath is quieter than speech but louder than silence, so it usually survives. If the cut lands right against the next word, the speaker can sound clipped. Lengthen Longer than slightly rather than lowering the threshold.
  • Music beds. A video with music playing under the voice never really goes silent, so the tool finds little to cut. Remove silences on the clean voice recording first, then add music afterwards.
  • Silent demonstrations. In a screen recording you may stay quiet while clicking through something important. Silence detection cannot see that, so it removes the demo too. Use a higher Longer than value, or cut those recordings by hand in iMovie.
  • Visible jumps. On a locked-off camera every cut is a small jump in position. That is the accepted look for vlogs, but for a formal talk you may prefer fewer, longer gaps.
  • Captions made too early. Captions timed to the original no longer match after cutting. Add captions last, for example with Adjust › Add auto-captions…, which transcribes the speech on your Mac and burns it into a new copy, plus an SRT.

A sensible order of work

Cut the start and end first with Cut › Trim…, so the silence tool is not working on footage you will throw away. Then remove silences, check the pacing, and only then add captions, crop to a vertical frame and compress for upload. Each FileDial tool saves a new copy, so use the latest result as the next input and delete the intermediate files at the end. Because every step runs on the Mac, an unreleased course or a client interview is never uploaded to a web service just to lose its pauses.

Questions

Can QuickTime Player remove pauses from the middle of a video?

Not in a practical way. Apple documents QuickTime's Edit > Trim for removing the parts before and after a selection, and it has no waveform or silence detection. For pauses in the middle, use iMovie's Split Clip by hand or a tool that detects quiet stretches automatically, such as FileDial's Cut › Remove silences…

Will removing silences put the audio out of sync?

Not with a tool that cuts picture and sound together. With FileDial's Cut › Remove silences…, the same stretch is removed from both, so speech stays in sync with the speaker's lips. Problems usually come from editing the audio separately, for example cleaning a voice track in one app and laying it back over untouched video.

What is a good silence threshold for a talking-head video?

Start with FileDial's defaults, -35 dB for Quieter than and 0.6 seconds for Longer than, and run them on a short sample. If nothing is cut, the room is noisy, so raise the level a little. If quiet words vanish, lower it. For calm teaching videos, a longer minimum gap keeps natural pauses.

Does FileDial upload my video to remove silences?

No. All the work happens on your Mac, and the tool works with Wi-Fi off. The result is saved as a new file beside the original, which stays unchanged, and every result has Undo. That suits unreleased courses, client interviews and other recordings you would rather not hand to a web service.

Sources

  1. Apple Support: Trim a movie or clip in QuickTime Player on Mac
  2. Apple Support: Trim and arrange videos and photos in iMovie
  3. Wikipedia: Jump cut

Related

Try FileDial free for 1 daySee the dialNo card, no account. Then $6.99 once, for 2 Macs. Runs offline on macOS 14+ (Apple silicon).